<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[如何解决步进驱动器的误差问题]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271.html]]></link>
 <description><![CDATA[Latest 50 replies of 如何解决步进驱动器的误差问题]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Fri, 01 May 2026 05:51:06 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[其实这个软件上可以想办法的，主要是程序做起来可能比较麻烦，必须知道1圏多少个脉冲同时还要知道具体走的距离，通过计算最终就不会有累积误差存在,]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#888241.html]]></link>
 <author><![CDATA[xlxlab]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 22 Oct 2010 06:04:08 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[增大细分,使脉冲当量减小,使误差在容许范围内. [s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#886246.html]]></link>
 <author><![CDATA[yanzhi2008]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 Oct 2010 05:28:43 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第8楼佳史于2010-10-19 09:18发表的&nbsp;&nbsp;:

喜欢这个回答，这句话也是我想说的。哈
[/quote]
每个人都型这么做，这样那就太顺了了，你发现问题后以后在做之前就知道该选什么样的控制器了，不要最后什么硬件都好了，发现软件不行，设计前硬件和软件就要仪器考虑，要沟通。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#886107.html]]></link>
 <author><![CDATA[niningtt]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 Oct 2010 01:26:38 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;选硬件的时候要事先选好，不要等丝杆和步进的细分无法匹配的时候，在程序上下文章。方向都走错了，其它都是挽救错误而已。
&nbsp;&nbsp; 因为选型的工程师没有选好丝杆和步进匹配，后来还怀疑我的程序没有做好，于是被我狠狠的批评了一顿。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#886105.html]]></link>
 <author><![CDATA[佳史]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 Oct 2010 01:23:06 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第4楼jxh668于2010-10-18 11:25发表的&nbsp;&nbsp;:
最好能调整细分数，计算时能整除是个好习惯
[/quote]
喜欢这个回答，这句话也是我想说的。哈]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#886103.html]]></link>
 <author><![CDATA[佳史]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 Oct 2010 01:18:52 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第2楼niningtt于2010-10-18 11:19发表的&nbsp;&nbsp;:
软件没法实行的就改变硬件啊，用个减速机，齿轮比你自己根据精度需要选啊，只要有10：1的，你的不久搞定了吗
[/quote]
谢谢回答，说得有些道理。
选硬件的时候要事先选好，不要等丝杆和步进的细分无法匹配的时候，在程序上下文章。方向都走错了，其它都是 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#886102.html]]></link>
 <author><![CDATA[佳史]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 Oct 2010 01:16:43 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[在最后需要输出的脉冲量上四舍五入，影响不大。不能舍去0.3.]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#885706.html]]></link>
 <author><![CDATA[hardy_6817]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Oct 2010 08:07:11 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[那你换个伺服，要不就加个减速齿轮]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#885571.html]]></link>
 <author><![CDATA[niningtt]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Oct 2010 03:27:42 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[最好能调整细分数，计算时能整除是个好习惯]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#885569.html]]></link>
 <author><![CDATA[jxh668]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Oct 2010 03:25:40 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[也可以用定位指令用绝对位置定位指令，这样就不会有积累误差了最多也就是差0.4/26.3*0.1MM,大概0.00152MM，估计你的机械精度都达不到这个值把]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#885568.html]]></link>
 <author><![CDATA[niningtt]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Oct 2010 03:24:51 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[软件没法实行的就改变硬件啊，用个减速机，齿轮比你自己根据精度需要选啊，只要有10：1的，你的不久搞定了吗]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#885565.html]]></link>
 <author><![CDATA[niningtt]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Oct 2010 03:19:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[0.1毫米需要23.3个脉冲，那么在PLC里面就做了四舍五入取23个脉冲，所以相当于每走0.1毫米，就丢掉0.3个脉冲，如此累计，走的实际距离越长，误差越大。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-82271#885500.html]]></link>
 <author><![CDATA[佳史]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Oct 2010 01:39:15 +0000]]></pubdate>
</item>
</channel></rss>