<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[如何用万用表判断电机是否烧坏]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462.html]]></link>
 <description><![CDATA[Latest 50 replies of 如何用万用表判断电机是否烧坏]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Wed, 29 Apr 2026 11:36:07 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[首先用电阻档测量线圈是否接地 在分别量三项是否通的 不通则是坏的]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#640128.html]]></link>
 <author><![CDATA[感悟人生]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 04 Oct 2009 12:34:48 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[s:21]&nbsp;[color=#0000ff]以三相异步电动机为例说明[/color]
[color=#ff0000]1,断开电源线,切记![/color]
[color=#ff0000]2,将电机接线盒内的连接片去除[/color]
[color=#ff0000]3,将万用表打到电阻档,量程选*200K就可以,测三相绕组对机壳的绝缘情况,结果应该为1既是无穷大,否则就可判定为电动机有故障的;[/color]
[co ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#639476.html]]></link>
 <author><![CDATA[youlong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 03 Oct 2009 05:39:16 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[潜水电机光凭是否接地不能判断电机是否烧坏，进水也会接地但不一定电机就烧了]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#637094.html]]></link>
 <author><![CDATA[shklby]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 29 Sep 2009 01:47:53 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[把电机接线端的短接片全部拆掉,用万用表测3对绕组,看电阻是否平衡,然后再测两两绕组之间是否有电阻.对地的话最好用1000V的摇表测]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#634606.html]]></link>
 <author><![CDATA[anddylihua]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Sep 2009 15:49:39 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[先把三相电源线断开，然后万用表测量三相电阻是否平衡。或者测量对地电阻]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#634458.html]]></link>
 <author><![CDATA[zhidaoshenmo]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Sep 2009 13:44:23 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第1楼注册中心于2009-09-25 10:47发表的&nbsp;&nbsp;:
先用*1000K电阻档测三相绕组对地的绝缘,至少应为0.5M以上,越大越好,否则就可判定为坏的;再用*1电阻档分别测三相绕组之间的电阻,应都是通的,否则就可判定为坏的;然后可根据三相电阻值的差别判断绕组是否有缺陷,这一点单凭万用表一般不容易判断.
[/quote]
估 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#634295.html]]></link>
 <author><![CDATA[wslok]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Sep 2009 09:33:54 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[先用*1000K电阻档测三相绕组对地的绝缘,至少应为0.5M以上,越大越好,否则就可判定为坏的;再用*1电阻档分别测三相绕组之间的电阻,应都是通的,否则就可判定为坏的;然后可根据三相电阻值的差别判断绕组是否有缺陷,这一点单凭万用表一般不容易判断.]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-46462#633978.html]]></link>
 <author><![CDATA[注册中心]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Sep 2009 02:47:25 +0000]]></pubdate>
</item>
</channel></rss>