<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[PLC开关量外部输入线路过长输入不稳定如何 ..]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828.html]]></link>
 <description><![CDATA[Latest 50 replies of PLC开关量外部输入线路过长输入不稳定如何 ..]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Tue, 05 May 2026 16:15:29 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用两组电源和中继&nbsp;&nbsp;把中间接线位置加上中继 线圈电源和PLC电源独立]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527465.html]]></link>
 <author><![CDATA[森利德]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 15:06:48 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[加一个继电器。外部长线路用高电压，接继电器线圈，继电器触点再接PLC，这样转换一下]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527464.html]]></link>
 <author><![CDATA[zsfjn]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 14:05:20 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用楼主陋室居士于2025-09-11 09:16发表的 PLC开关量外部输入线路过长输入不稳定如何解决 :
现在的情况是，PLC距离外部输入触点约200米，线路为1.5平方，外部输入点偶尔会导致PLC输入点不能触发的问题，不知有没什么好方法解决。
[/quote]
应该跟电缆粗细有关系，200m，考虑压降影响，换醋一级的电缆看看，有屏蔽 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527448.html]]></link>
 <author><![CDATA[dalao123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 11:10:01 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[使用AC220V的模块]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527427.html]]></link>
 <author><![CDATA[yiyang1]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 07:55:21 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[哦，对了。如果你的外部输入点信号是开关量（行程开关等机械触点式），我觉得问题不大，你仔细检查一下有没有虚接；如果外部输入信号是传感器(NPN 或者PNP），可能会由于返回电流弱PLC无法接收，需要把传感器输出的信号转换为开关信号。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527405.html]]></link>
 <author><![CDATA[朱光显]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 05:55:52 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我之前在现场测试过，同一根电缆从A点出发到B点然后返回到A点（B点中继接通电缆其中两根线），在A点测量到的压降也只有2.5V，两地相距200M,电缆是2.5平方，中间没有接头，PLC接收信号没有问题。
开始我们这根电缆上控制电压是220V，由于线路过长产生感应电，后来把控制电压换成DC24V就可以了。
楼主可以更换粗的电缆，或者 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527399.html]]></link>
 <author><![CDATA[朱光显]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 05:46:05 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[给开关电源电压调一点到25V多]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527382.html]]></link>
 <author><![CDATA[wsxw40]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 03:39:49 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[加磁环屏蔽防干扰]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527377.html]]></link>
 <author><![CDATA[zhuyongxiong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 03:20:19 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[应该没啥问题]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527368.html]]></link>
 <author><![CDATA[张梧桐]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 02:43:14 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[最好用IO扩展模块，然后走通讯。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527362.html]]></link>
 <author><![CDATA[gengjie]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 02:06:29 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用楼主陋室居士于2025-09-11 09:16发表的 PLC开关量外部输入线路过长输入不稳定如何解决 :
现在的情况是，PLC距离外部输入触点约200米，线路为1.5平方，外部输入点偶尔会导致PLC输入点不能触发的问题，不知有没什么好方法解决。
[/quote]

(线路为1.5平方)就屏这句话推断选财和布线存在问题吧！]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527358.html]]></link>
 <author><![CDATA[二手工控电器]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 01:49:35 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[不费劲，直接换无线传输模块，
费劲 换RVVP电缆]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527353.html]]></link>
 <author><![CDATA[li19930121]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 01:35:38 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[可以用远程模块&nbsp;&nbsp; 
信号衰减也可以用中继放大]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1786828#2527352.html]]></link>
 <author><![CDATA[wangnaizhi]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 11 Sep 2025 01:28:20 +0000]]></pubdate>
</item>
</channel></rss>