<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[驱动器未开使能的前提下，用手转动伺服电 ..]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691.html]]></link>
 <description><![CDATA[Latest 50 replies of 驱动器未开使能的前提下，用手转动伺服电 ..]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Fri, 15 May 2026 02:12:39 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[可以 伺服 不ON 也可以 把伺服后面的 编码器反馈 信号 接回PLC&nbsp;&nbsp;计数 这样就 知道 你OFF的时候的&nbsp;&nbsp;手动移动量了啊]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2035758.html]]></link>
 <author><![CDATA[635590445]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 28 Mar 2019 09:12:38 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[要手拉做什么？不能做个点动让它移到你要位置吗？点动前 把位置清0 就行了，]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2035507.html]]></link>
 <author><![CDATA[huiyang]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 27 Mar 2019 07:10:49 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[回原点，后直接定位到需要位置。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034703.html]]></link>
 <author><![CDATA[dalao123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 23 Mar 2019 01:26:03 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[可以选用绝对值编码器哦]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034699.html]]></link>
 <author><![CDATA[songbo198x]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 23 Mar 2019 00:30:53 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[这个用运动控制卡直接就能读出来,PLC应该是没这个功能?或者没那么容易实现?]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034655.html]]></link>
 <author><![CDATA[佛系少年武功]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 22 Mar 2019 11:06:36 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第6楼seallyzoom于2019-03-20 16:37发表的&nbsp;&nbsp;:

一定非用绝对式，增量的不行？
[/quote]
除非走通讯RS232或485]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034330.html]]></link>
 <author><![CDATA[enderz]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 21 Mar 2019 03:11:08 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[既然用了PLC与伺服，还要手动推电机/机构？这设计貌似不够科学。除非是检修，可检修后也必须重新复归原点呀。
如果非要让PLC记住大概位置，程序中我的做法是：(以 FX1S为例)
LD&nbsp;&nbsp;M8002
DMOV&nbsp;&nbsp;D140&nbsp;&nbsp;D8140
LD&nbsp;&nbsp;M8000
OUT&nbsp;&nbsp;T0&nbsp;&nbsp;K20
AND&nbsp;&nbsp;T0
DMOV&nb ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034320.html]]></link>
 <author><![CDATA[zhong1946]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 21 Mar 2019 02:19:47 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第5楼xiaoyong898于2019-03-20 16:17发表的&nbsp;&nbsp;:
选择绝对式编码器伺服，还要支持通信的。
[/quote]
一定非用绝对式，增量的不行？]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034212.html]]></link>
 <author><![CDATA[seallyzoom]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Mar 2019 08:37:39 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[选择绝对式编码器伺服，还要支持通信的。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034209.html]]></link>
 <author><![CDATA[xiaoyong898]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Mar 2019 08:17:54 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[如果手动移动之前没有回原点，则使能后位置不准]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034203.html]]></link>
 <author><![CDATA[ma924888027]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Mar 2019 07:54:21 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第1楼xff000于2019-03-20 13:20发表的&nbsp;&nbsp;:
JOG运行到定位点，记录运行脉冲数，再传送给自动运行目标位置？ [s:26]
[/quote]
差不多这个意思，是伺服ON未开，人为移动定点记录]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034176.html]]></link>
 <author><![CDATA[seallyzoom]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Mar 2019 06:21:58 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[可以，从新上电要先回原点。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034163.html]]></link>
 <author><![CDATA[342703002]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Mar 2019 05:37:50 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[JOG运行到定位点，记录运行脉冲数，再传送给自动运行目标位置？ [s:26]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1664691#2034159.html]]></link>
 <author><![CDATA[xff000]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Mar 2019 05:20:53 +0000]]></pubdate>
</item>
</channel></rss>