<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[大家好，只有一个方向运行，定位要求很准 ..]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244.html]]></link>
 <description><![CDATA[Latest 50 replies of 大家好，只有一个方向运行，定位要求很准 ..]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Mon, 11 May 2026 11:02:20 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第9楼langui于2018-08-11 11:12发表的&#160;&#160;:
建议你和做冲压模的人咨询下，模具里面都有定位孔的，就算100W里面的模具也有定位针，这个主要是导正因为误送导致的误差。冲压送料一般就两种，滚轮送料机和夹式送料机，滚轮的好处就是可以随意设置长度，一般设定长度是0.01-999.99，送料频率和精度稍差，夹 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1992052.html]]></link>
 <author><![CDATA[bestmanyin]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 11 Aug 2018 06:13:37 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[学习了]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1992047.html]]></link>
 <author><![CDATA[麦小兜]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 11 Aug 2018 06:02:20 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[建议你和做冲压模的人咨询下，模具里面都有定位孔的，就算100W里面的模具也有定位针，这个主要是导正因为误送导致的误差。冲压送料一般就两种，滚轮送料机和夹式送料机，滚轮的好处就是可以随意设置长度，一般设定长度是0.01-999.99，送料频率和精度稍差，夹式送料机的好处就是精度高，速度快，缺点就是送料长度很短，估计 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1992007.html]]></link>
 <author><![CDATA[langui]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 11 Aug 2018 03:12:41 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[感谢7楼指正，因为要求送料机定位很准，先冲孔后冲外形，并且两个产品中间没有任何间隙，一个接着一个。滚轮打滑等外部因素不知道精度能不能达到。如果不用滚轮，用什么代替好点，有做过这块的吗]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991983.html]]></link>
 <author><![CDATA[bestmanyin]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 11 Aug 2018 01:40:11 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[NC送料机99.99的人都用增量的，就你一个人用绝对的，每次你走10mm，你的数字就得10.00，20.00.这样增加，当冲个10K的时候，数字就到1000000.00了，你觉得对其来方便么?还有程序上每冲一次你就要更新一次。NC送料机的精度都不是很高，大多数都的用同步带+齿轮传送的，同步带有弹性，齿轮都有间隙。98%的NC都有放松装置，如 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991956.html]]></link>
 <author><![CDATA[langui]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 11 Aug 2018 00:23:45 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[三菱伺服有一个定长进给，你把软上限下限禁用，也可以]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991953.html]]></link>
 <author><![CDATA[鳝变的男人]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 11 Aug 2018 00:13:22 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[是不是不用绝对值编码器伺服，用增量型的伺服就可以了吧]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991948.html]]></link>
 <author><![CDATA[bestmanyin]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 10 Aug 2018 14:33:31 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[安川绝对值电机有无限轴功能，了解一下啊、 [s:26]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991935.html]]></link>
 <author><![CDATA[安川电机]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 10 Aug 2018 12:54:48 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用楼主bestmanyin于2018-08-10 17:39发表的 大家好，只有一个方向运行，定位要求很准，怎么控制 :
有台送料设备，准备用伺服+滚轮，送3米长的长条料进冲床，每次送进距离一致。准备用绝对值编码器伺服，伺服只用过来回旋转的，一个方向的没有用过
请问，
1、一个方向绝对值伺服怎么控制啊，每次走相对距离吗
2、 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991928.html]]></link>
 <author><![CDATA[libenlong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 10 Aug 2018 12:34:18 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[很有道理]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991925.html]]></link>
 <author><![CDATA[cc自动化]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 10 Aug 2018 12:31:24 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[如果永远向一个方向旋转，而且总距离累加起来很长，那最好用相对定位了，这个定位也精准的

或者你绝对走到位置后，把当前值清零]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1654244#1991904.html]]></link>
 <author><![CDATA[ymmfa]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 10 Aug 2018 09:59:51 +0000]]></pubdate>
</item>
</channel></rss>