<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[步进电机控制分度盘]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142.html]]></link>
 <description><![CDATA[Latest 50 replies of 步进电机控制分度盘]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Tue, 28 Apr 2026 21:02:29 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[细分怎么调分24份都是小会有小数，若一定非要这样做又不想有误差，可以考虑加一个24能除尽的减速机就能轻松制定。也没有什么误差了。成本就多300大洋的事。但对设备来说不同凡想。你懂的]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981991.html]]></link>
 <author><![CDATA[yrm258]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 26 Jun 2018 05:18:37 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[分度盘&nbsp;&nbsp;都是一个传感器&nbsp;&nbsp;再用个调速电机控制&nbsp;&nbsp;&nbsp;&nbsp;算好驱动角和停止角的角度&nbsp;&nbsp;&nbsp;&nbsp;然后做个扇形遮光片&nbsp;&nbsp;传感器用的U型槽传感器 就可以了]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981989.html]]></link>
 <author><![CDATA[小八哥]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 26 Jun 2018 05:13:09 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[支持续3楼的做法]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981986.html]]></link>
 <author><![CDATA[汪传福]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 26 Jun 2018 05:10:05 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[步进电机是1.8°步进角的。每一等分的脉冲数=(200X细分数)/等分数（24）.]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981968.html]]></link>
 <author><![CDATA[haiyouyang]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 26 Jun 2018 04:03:22 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[只要扭矩够，速度慢，3楼的方法没有问题，之前做过类似转盘机构，我的方法，用取整指令，把脉冲取整数，小数部分的数值每次累加，累加值超过1时，实际脉冲数+1，剩余小数部分继续累加。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981954.html]]></link>
 <author><![CDATA[绝世精灵]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 26 Jun 2018 03:39:33 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我劝你不要用步进去控制分度盘，除非你到一定时间回一次原点，步进怎么都有丢步，速度越高越明显，当丢步脉冲到了一个分度的脉冲就看出来了。也许是走10次，也许是100次，也许的500次，但是慢慢的肯定就不在位置上了。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981932.html]]></link>
 <author><![CDATA[langui]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 26 Jun 2018 02:38:41 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[细分设大一点&nbsp;&nbsp; 比如20000&nbsp;&nbsp; 24等分&nbsp;&nbsp;拿16个位置设成833个脉冲&nbsp;&nbsp; 拿8个位置设成834个脉冲&nbsp;&nbsp;然后把脉冲间隔起来&nbsp;&nbsp; 833,833,834.....这样就行&nbsp;&nbsp; 位置多了一个脉冲基本上没啥影响&nbsp;&nbsp;这个影响还不及步进电机本身的精度影响&nbsp;&nbsp;这样做 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981816.html]]></link>
 <author><![CDATA[nightblueblu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 25 Jun 2018 09:03:34 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[400/24= 16.6666&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;1600/24=66.66666&nbsp;&nbsp;有小数点，影响数度 。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981763.html]]></link>
 <author><![CDATA[huiming]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 25 Jun 2018 07:14:12 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[选哪个细分除以24就是脉冲数]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1652142#1981741.html]]></link>
 <author><![CDATA[weijishanggu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 25 Jun 2018 05:48:04 +0000]]></pubdate>
</item>
</channel></rss>