<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[怎样用plc实现功牙机的控制]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046.html]]></link>
 <description><![CDATA[Latest 50 replies of 怎样用plc实现功牙机的控制]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Mon, 18 May 2026 12:49:10 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[你可以了解下 日本的速技能。。。我们做这种打孔 攻牙 去披锋。精度没的说。专门用在化油器上的。还有对钻头 丝锥 要求比较高。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926696.html]]></link>
 <author><![CDATA[蒲城风信子]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 10 Oct 2017 00:49:04 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[2MM以下的可以]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926687.html]]></link>
 <author><![CDATA[汪传福]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 23:55:44 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[不会攻完丝后丝口都撸了。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926686.html]]></link>
 <author><![CDATA[泰山之石]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 23:51:10 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[一秒不太可能~~還要建議一個~~
絲攻要檢測及牙要檢測
還要大量切削油]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926662.html]]></link>
 <author><![CDATA[lin10663]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 12:20:57 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[从机械角度给你分析一下运动&nbsp;&nbsp; 攻牙一般是前进一段&nbsp;&nbsp;退一小段&nbsp;&nbsp; 再前进一段&nbsp;&nbsp; 再退一小段&nbsp;&nbsp; 如此循环直到攻牙完成
&nbsp;&nbsp;如果直接攻到底&nbsp;&nbsp; 软材料像铝合金的还好&nbsp;&nbsp; 如果是钢件&nbsp;&nbsp; 你多少把丝锥都不够用&nbsp;&nbsp; 直接崩断了&nb ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926596.html]]></link>
 <author><![CDATA[nightblueblu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 06:59:25 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[都是大神啊 [s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926593.html]]></link>
 <author><![CDATA[工控剑侠666]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 06:54:52 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第10楼蒲城风信子于2017-10-09 09:07发表的&nbsp;&nbsp;:
没有那么复杂吧。我们攻牙机就普通的东力的正反转带调速电机就行。正反转。用两个接近传感器感应就行
[/quote]
1S钟完成动作呀，你要看清要求呀]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926564.html]]></link>
 <author><![CDATA[汪传福]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 04:10:44 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[没有那么复杂吧。我们攻牙机就普通的东力的正反转带调速电机就行。正反转。用两个接近传感器感应就行]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926530.html]]></link>
 <author><![CDATA[蒲城风信子]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 09 Oct 2017 01:07:03 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[攻牙机，我到时给别人搞过好几套呀， 我都是用伺服做的，用步进不太现实，1秒钟攻好的话，2.0以下的板材可以呀，以上就很难了，太快会断丝锥]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926465.html]]></link>
 <author><![CDATA[汪传福]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 08 Oct 2017 10:36:15 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[只要能实现进退和正反转就可以了，最好在机械结构上想想办法
另外想一秒攻好的话要看攻牙的深度，如果是3MM以内的通孔应该是可以，其它的不太现实。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1926463.html]]></link>
 <author><![CDATA[周家大少]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 08 Oct 2017 09:43:37 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[不知道你是用牙套还是用两个同步控制，用牙套的话可以用步进马达，用两个马达同步控制的话，最好是用伺服，可以保证机构部分不用动了，你只需要在程序和伺服调节上想办法就可以了。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925993.html]]></link>
 <author><![CDATA[langui]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 05 Oct 2017 11:24:25 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[特别是小丝攻，力小了攻不进，力大了会断的。还有攻的深度，过了也会断，只怕想很快的速度很难实现。建议用带反馈的伺服电机，控制力度和深度。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925923.html]]></link>
 <author><![CDATA[十三月]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 05 Oct 2017 01:47:49 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我是来学习的。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925867.html]]></link>
 <author><![CDATA[ccy5156]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 04 Oct 2017 10:14:05 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第1楼hu198812于2017-10-03 18:03发表的&nbsp;&nbsp;:
一般用伺服控制，采用位置加扭力控制
[/quote]
是用位置作为旋转，扭力作为进给吗?]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925829.html]]></link>
 <author><![CDATA[高州龙]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 04 Oct 2017 00:19:37 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[步进攻牙？
晕哦 攻是可移动，能不能攻好鬼知道
建议用扭力电机，带反馈的，或者用伺服
我用过韩国的扭力电机]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925809.html]]></link>
 <author><![CDATA[不小心遇见你]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 03 Oct 2017 11:10:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[一秒钟完成攻牙的动作,&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 有点不太可能]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925805.html]]></link>
 <author><![CDATA[tkggtdkjpl]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 03 Oct 2017 10:49:08 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[一般用伺服控制，采用位置加扭力控制]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1633046#1925803.html]]></link>
 <author><![CDATA[hu198812]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 03 Oct 2017 10:03:54 +0000]]></pubdate>
</item>
</channel></rss>