<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[驱动器如何接线]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1630824.html]]></link>
 <description><![CDATA[Latest 50 replies of 驱动器如何接线]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Fri, 10 Apr 2026 10:57:11 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[驱动器上面一般写了输入5-24V信号 ，可以输24V&#160;&#160;，但是一般在信号端串一个1.8K或2K电阻比较好，供电电压在供电范围内就可以了&#160;&#160;，但是电压越接近上限驱动器工作越好
 脉冲PUL-&nbsp;&nbsp;方向DIR-都串电阻[s:26]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1630824#1922469.html]]></link>
 <author><![CDATA[nightblueblu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 Sep 2017 00:38:24 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[下面那个驱动器电路板拍背面 看下引脚去哪了 
完全靠猜 搞不好烧驱动器
我估计 右边6个接口的从左到右分别 V+ V- A+ A- B+ B-
中间四个接口的位PLS+ PLS- DR+ DR-
最左边是使能]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1630824#1922042.html]]></link>
 <author><![CDATA[不小心遇见你]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Sep 2017 02:07:24 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[从左到右&nbsp;&nbsp;
 V+&nbsp;&nbsp;V-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; A+ A- B+ B-&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&n ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1630824#1922034.html]]></link>
 <author><![CDATA[nightblueblu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Sep 2017 01:41:50 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[最左边应该是电源输入，中间就是接马达线，先用表量出来两相，然后接就是了，最右边应该是信号接入 [s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1630824#1921992.html]]></link>
 <author><![CDATA[周家大少]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 Sep 2017 13:26:08 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[步进&nbsp;&nbsp;几相的&nbsp;&nbsp;先把对应的相找出来 然后再再接线 相线不分正负 对应相也不需要分]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1630824#1921954.html]]></link>
 <author><![CDATA[wangnaizhi]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 Sep 2017 10:58:18 +0000]]></pubdate>
</item>
</channel></rss>