<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[有懂油压系统的朋友吗？]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301.html]]></link>
 <description><![CDATA[Latest 50 replies of 有懂油压系统的朋友吗？]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Sun, 10 May 2026 10:57:44 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[油缸下降的速度快慢是靠油的流量来控制，跟压力没有关系，你要换大流量低压力的油泵，还有你的进油管大小有关，回油的孔径大小有关。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917883.html]]></link>
 <author><![CDATA[liyanjunx]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 30 Aug 2017 13:23:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[上升要求越快越好；下降同样如此；在不增加大的成本的话；可以在上升阀上并联一个口径大一点的2位3通阀；上升关闭；下降打开；这样增加回油流量；仅供参考；]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917360.html]]></link>
 <author><![CDATA[zmy450365]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 29 Aug 2017 00:56:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[要计算一下，分析后才能改的，还是要按原理计算的。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917353.html]]></link>
 <author><![CDATA[wqing]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 29 Aug 2017 00:36:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[单柱液压缸是否工作原理根千斤顶一样呢？如果这样只需要增加快排阀系统就可以。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917316.html]]></link>
 <author><![CDATA[泰山之石]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 29 Aug 2017 00:00:10 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用楼主yushli2002于2017-08-27 10:54发表的 有懂油压系统的朋友吗？ :
我公司单柱25T油压机，生产部嫌弃下降速度太慢。我更换了油泵和电磁换向阀后，下压速度没有什么提高。我想是不是要加一套增压系统，向主缸增压加快下降速度。但不知道怎么添加，有懂的朋友能否提供好的方案。
[/quote]
首先要确定你过去的控 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917263.html]]></link>
 <author><![CDATA[wul2.4g]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 28 Aug 2017 11:17:39 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[液压快速回路主要有差动和充液阀，直接更换换向阀口径提速效果不会很明显的。 [s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917258.html]]></link>
 <author><![CDATA[电工小安子]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 28 Aug 2017 10:40:46 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[油缸的速度V取决于供/回油流量（与系统压力P无关），所以你要计算油泵流量，油管管径、节流阀]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917233.html]]></link>
 <author><![CDATA[往事如风]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 28 Aug 2017 09:03:18 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;下降速度太慢

&nbsp;&nbsp;&nbsp;&nbsp; 增加流量。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917015.html]]></link>
 <author><![CDATA[zhtokokk]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 08:28:22 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[最好的办法就是加大油泵排量加大电机功率，改液压的工作量就比较大了，改差动式你的重新设计阀板，改内差动的话你的改油缸结构和阀板]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1917014.html]]></link>
 <author><![CDATA[qcb8888]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 08:19:44 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[如果是轴向柱塞泵的话可以调节倾向盘的角度改变液压油流量，从而改变速度。如果要调节压力就调节溢流阀的开度]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1916996.html]]></link>
 <author><![CDATA[lenghai]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 06:47:24 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[单柱25T油压机，单柱是柱塞缸，单向进油上顶，下降靠自重把油压出来，换阀没用。
只有改成活塞缸，或者增加拉模缸，才能增加下降速度。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1916989.html]]></link>
 <author><![CDATA[znz43]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 06:35:03 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我也觉得还是问一下厂家怎么改装好一点，毕竟有一些参数厂家最清楚了。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1916965.html]]></link>
 <author><![CDATA[周家大少]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 05:59:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用楼主yushli2002于2017-08-27 10:54发表的 有懂油压系统的朋友吗？ :
我公司单柱25T油压机，生产部嫌弃下降速度太慢。我更换了油泵和电磁换向阀后，下压速度没有什么提高。我想是不是要加一套增压系统，向主缸增压加快下降速度。但不知道怎么添加，有懂的朋友能否提供好的方案。
[/quote]液压系统比较复杂，除了 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1916947.html]]></link>
 <author><![CDATA[tingfenghu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 03:58:09 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[微信15935711469，给你建议。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1916945.html]]></link>
 <author><![CDATA[好久不见啦！]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 03:49:06 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[首先你要速度快！！！但是要快到什么程度？要有个数值！你目前是什么速度？需要达到什么速度？你只要加大泵流量就行，压力不可过大，]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1624301#1916944.html]]></link>
 <author><![CDATA[二手工控电器]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Aug 2017 03:44:47 +0000]]></pubdate>
</item>
</channel></rss>