<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[转盘涂胶设备]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368.html]]></link>
 <description><![CDATA[Latest 50 replies of 转盘涂胶设备]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Sat, 11 Apr 2026 17:29:42 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[这就是没事找事系列
为什么不每个工位装一个检测开关]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1916353.html]]></link>
 <author><![CDATA[adnnin]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 24 Aug 2017 08:50:25 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[转盘时等分的话可以计算第一个工位到第二个工位需要发多少脉冲，当每个工位完成相关动作后走这个脉冲量，用光电开关控制是否动作]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1916337.html]]></link>
 <author><![CDATA[年华犹存]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 24 Aug 2017 08:29:02 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第12楼绝世精灵于2017-05-04 18:47发表的&nbsp;&nbsp;:

赞同，之前做过转盘式组装机就用移位配合角度
[/quote]

赞同,用移位检测有无料，角度控制位置喷涂]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1886423.html]]></link>
 <author><![CDATA[hardy_6817]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 05 May 2017 10:38:51 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[老铁，我看了好久才明白，控制逻辑好复杂啊，转盘上的每个工件在不同的位置都要喷胶，还不止一个，感觉中间很容易逻辑混乱或者数据混乱，加工类型太多，加工件数量也太多，程序逻辑想想都乱....]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1886414.html]]></link>
 <author><![CDATA[ning244687]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 05 May 2017 09:35:16 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[为什么不每个工位装一个检测开关]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1886386.html]]></link>
 <author><![CDATA[sccgkong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 05 May 2017 08:17:26 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用移位指令，比较方便]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1886166.html]]></link>
 <author><![CDATA[yjq]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 04 May 2017 12:57:38 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第10楼min0326于2017-05-04 11:34发表的&nbsp;&nbsp;:
转盘是不是等分的，如果是等分的可以用位移指令ＳＦＴＲ或ＳＦＴＬ，一个感应检测工位，一个检测有没有料，你可以看下手册。
[/quote]
赞同，之前做过转盘式组装机就用移位配合角度]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1886142.html]]></link>
 <author><![CDATA[绝世精灵]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 04 May 2017 10:47:03 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[准备4个存储区对应4个喷枪，检测到工位有工件，就在现有位置基础上加上对应喷枪的起喷点和停喷点距离。
做一个循环，监测现有转盘位置是否到各个喷枪的起喷点和停喷点之内，是就喷，喷完清除相应存储区的数据。
在编码器清零点可以吧区域分为起喷点到终点，和0点到停喷点两个比较区域。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1886135.html]]></link>
 <author><![CDATA[fubin739]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 04 May 2017 10:37:06 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[转盘是不是等分的，如果是等分的可以用位移指令ＳＦＴＲ或ＳＦＴＬ，一个感应检测工位，一个检测有没有料，你可以看下手册。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885976.html]]></link>
 <author><![CDATA[min0326]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 04 May 2017 03:34:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用編碼器既使再高速如C250之類還是有誤差
會導致入料不順~~除非你都能吸收掉那誤差
否則短暫停機率高~~要考慮用分割器則比較好]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885136.html]]></link>
 <author><![CDATA[lin10663]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 10:53:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第7楼zhaoxg于2017-04-30 15:23发表的&nbsp;&nbsp;:
我看没有那么复杂！
高速计数，计数值大于一个工位数后移位一次标志位，同时计数器减去工位数，工位数值为一个工位对应编码器脉冲数，再检查每个工位是否有瓶做相应动作
[/quote]

谢谢这位朋友的方法，可以试试，这里有什么方法可以判断前面已经走过的工位 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885133.html]]></link>
 <author><![CDATA[lddl123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 09:58:13 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我看没有那么复杂！
高速计数，计数值大于一个工位数后移位一次标志位，同时计数器减去工位数，工位数值为一个工位对应编码器脉冲数，再检查每个工位是否有瓶做相应动作]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885115.html]]></link>
 <author><![CDATA[zhaoxg]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 07:23:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第4楼xxl123于2017-04-30 11:34发表的&#160;&#160;:
三菱高速计数器不是有硬件复位吗？软件复位也行。转一圈复位一次。编码器数值等于多少时加上控制条件使喷头1工作。其它都一样。多个位置要工作就并联条件就行了。
[/quote]

谢谢这位朋友， 复位高速计数器我明白，我觉得难点是高速计数器复位后，后面的工件 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885109.html]]></link>
 <author><![CDATA[lddl123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 04:18:39 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第3楼sosyou于2017-04-30 10:54发表的&nbsp;&nbsp;:
不知道这样行不行
两上光电开关一个确定有没有工件 一个确定转盘旋转， 要求工件的距离不能有太大的误差 然后用位左移指令
sfltp&#160;&#160;m100 m0 k18 k1 
m8 out y0 4号枪
m11 out y1 3
.......
[/quote]



谢谢这位朋友，编码器是用来计算行走距离，距 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885106.html]]></link>
 <author><![CDATA[lddl123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 03:56:23 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[三菱高速计数器不是有硬件复位吗？软件复位也行。转一圈复位一次。编码器数值等于多少时加上控制条件使喷头1工作。其它都一样。多个位置要工作就并联条件就行了。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885102.html]]></link>
 <author><![CDATA[xxl123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 03:34:27 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[不知道这样行不行
两上光电开关一个确定有没有工件 一个确定转盘旋转， 要求工件的距离不能有太大的误差 然后用位左移指令
sfltp&#160;&#160;m100 m0 k18 k1 
m8 out y0 4号枪
m11 out y1 3
m14 out y2 2 
m17 out y3 1号枪
当工件传感器 感应到没有工件时 要马上复位m100 一个工件位，让这个工件位为0 下一个工件为有为1 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885092.html]]></link>
 <author><![CDATA[sosyou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 02:54:09 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[谢谢1楼朋友，怎样进行区域比较，高速计数器不知道什么时候清零]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885086.html]]></link>
 <author><![CDATA[lddl123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 02:17:03 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[高速计数并用区域比较。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1580368#1885084.html]]></link>
 <author><![CDATA[xxl123]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 30 Apr 2017 02:11:15 +0000]]></pubdate>
</item>
</channel></rss>