<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[伺服电机位置偏差问题]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430.html]]></link>
 <description><![CDATA[Latest 50 replies of 伺服电机位置偏差问题]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Sat, 11 Apr 2026 16:42:58 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第19楼sznczj于2015-12-27 09:34发表的&nbsp;&nbsp;:

我发表下我个人的见解
1，从你的描述上来看你的设备是做正反转的往返运动而不是做圆周运动，所以电子齿轮不论怎么设置都不会造成误差积累。

2，一般情况下机械结构有可能造成定位不准确，但一般不会造成误差的积累
.......
[/quote]
谢谢你的提议
&nbsp; ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730656.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Dec 2015 01:47:27 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用楼主wuzhishou于2015-12-25 10:14发表的 伺服电机位置偏差问题 :
伺服电机正转脉冲运行反正转回来到原点时候有点偏差每次有个几毫米，我这设备一个循环是12次，运行3个循环那就误差很大了
&nbsp;&nbsp; 电子齿轮比那里根据齿轮分度圆算下来有点小数点，我按4舍5入的方法设定的。运行时候也监控了脉冲没丢失
会 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730653.html]]></link>
 <author><![CDATA[sznczj]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Dec 2015 01:34:45 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第17楼namae于2015-12-26 21:11发表的&nbsp;&nbsp;:

我也不知这样算是否可以？不知你伺服编码器的分辨率是多少？
[/quote]
2500线4备频按10000算的]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730652.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Dec 2015 01:09:19 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第8楼wuzhishou于2015-12-25 14:10发表的&nbsp;&nbsp;:

链轮分度圆￠101减速机1；20&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;正常算出来的是分子100000 /分母18997他们的比率是5.26398905这么大的分子分母伺服驱动器参数设定不了最大只能到10000只有继续放小就成了小数点丢失了！
[/quote]
我也不知 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730600.html]]></link>
 <author><![CDATA[泰山之石]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 26 Dec 2015 13:11:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第15楼安徽精致酷龙于2015-12-26 09:33发表的&nbsp;&nbsp;:
10楼对的,伺服的精度是建立在机械的精度基础上的.根据我的经验,伺服的精度远超过我们一般机械所需精度.而实际工程中的这种误差大多数是机械设计不合理.你都用伺服了,还用链轮来做传动不合理.
[/quote]
从你分析各方面经验来看一定是实践经验丰富的高 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730352.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 26 Dec 2015 01:57:17 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[10楼对的,伺服的精度是建立在机械的精度基础上的.根据我的经验,伺服的精度远超过我们一般机械所需精度.而实际工程中的这种误差大多数是机械设计不合理.你都用伺服了,还用链轮来做传动不合理.]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730345.html]]></link>
 <author><![CDATA[安徽精致酷龙]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 26 Dec 2015 01:33:18 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第11楼老兔子于2015-12-25 19:42发表的&nbsp;&nbsp;:
这种来回造成的误差通常都是机械的问题，特别是你采用了减速器和链条传动更是这样。

按楼上（10楼）的办法解决也是不错的办法。
[/quote]
谢谢讲解！我现在总算是明白了，以后类是机械精度达不到的干脆用变频器来加信号控制都不搞伺服玩了
&nbsp;&nbsp;粗 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730339.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 26 Dec 2015 00:56:51 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第10楼whj4190于2015-12-25 17:54发表的&nbsp;&nbsp;:
机械精度达不到，减速器的精度也有关系，链轮带动链条正反转会有间隙的误差累积，看外部加传感器行不？我做个平面的循环转动，也是机械无精度，最后用速度模式，加传感器检测来停止
[/quote]
[s:28]速度模式好搞吗？我一直都是搞位置模式，找个时间一定要 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730338.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 26 Dec 2015 00:54:57 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[别忘记了万能的干扰 [s:26]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730313.html]]></link>
 <author><![CDATA[东莞工控]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 15:01:43 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[这种来回造成的误差通常都是机械的问题，特别是你采用了减速器和链条传动更是这样。

按楼上（10楼）的办法解决也是不错的办法。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730263.html]]></link>
 <author><![CDATA[老兔子]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 11:42:19 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[机械精度达不到，减速器的精度也有关系，链轮带动链条正反转会有间隙的误差累积，看外部加传感器行不？我做个平面的循环转动，也是机械无精度，最后用速度模式，加传感器检测来停止]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730232.html]]></link>
 <author><![CDATA[whj4190]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 09:54:13 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第6楼qianyonggang于2015-12-25 11:59发表的&nbsp;&nbsp;:
小数点会导致在不断的循环中逐步累积误差，但你的单个循环误差几毫米也太大了，检查机械部分
[/quote]
应该是的，机械精度确实粗糙，减速机联动轴上装的链轮带动链条，往复式正反转4.6米的高速跑。再说链轮的分度圆求圆周率又舍去小数点了，舍的太多了 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730155.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 06:18:45 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第5楼namae于2015-12-25 11:45发表的&nbsp;&nbsp;:
为什么电子齿轮要有小数点？那你的计算方式存在问题吧
[/quote]
链轮分度圆￠101减速机1；20&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;正常算出来的是分子100000 /分母18997他们的比率是5.26398905这么大的分子分母伺服驱动器参数设定不了最大只能到 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730143.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 06:10:51 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[是不是有干扰]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730114.html]]></link>
 <author><![CDATA[1234mm]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 05:34:11 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[小数点会导致在不断的循环中逐步累积误差，但你的单个循环误差几毫米也太大了，检查机械部分]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730057.html]]></link>
 <author><![CDATA[往事如风]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 03:59:33 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[为什么电子齿轮要有小数点？那你的计算方式存在问题吧]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730051.html]]></link>
 <author><![CDATA[泰山之石]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 03:45:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第3楼daiz63于2015-12-25 11:03发表的&nbsp;&nbsp;:
有偏差时，要查清3个位置，到底是谁的偏差
1.指令位置
2.反馈位置
3.机械位置
[/quote]
用的绝对定位指令DDRVA用的1对1脉冲当量，开机前机械自动找一次原点，正转负载运行下降，空载反转按要求要回到原点位置，现在每次空载回原点位置就不到位置少走了大概2 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730045.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 03:32:56 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[加原点。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730021.html]]></link>
 <author><![CDATA[静芳]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 03:01:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[大家有没遇到伺服位置丢失偏差问题了
&nbsp;&nbsp;&nbsp;&nbsp;不是同样的设备应该会有遇到同样的问题吧]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1536430#1730010.html]]></link>
 <author><![CDATA[wuzhishou]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 25 Dec 2015 02:27:39 +0000]]></pubdate>
</item>
</channel></rss>