<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[台达plc程序的定时器问题]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622.html]]></link>
 <description><![CDATA[Latest 50 replies of 台达plc程序的定时器问题]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Sat, 09 May 2026 10:54:07 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[把LD&nbsp;&nbsp; T0&nbsp;&nbsp;改成：
&nbsp;&nbsp;LDP&nbsp;&nbsp;&nbsp;&nbsp;T0
就OK啦 [s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1732015.html]]></link>
 <author><![CDATA[fengrunsheng]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 31 Dec 2015 01:51:45 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[t0&nbsp;&nbsp;y3 都在工作
改改就好了]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1731978.html]]></link>
 <author><![CDATA[杨一敏]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 30 Dec 2015 14:46:32 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[你需要怎样的动作，问题在X2上。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1730680.html]]></link>
 <author><![CDATA[幸运娃161]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Dec 2015 02:53:31 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[似乎程序上就是在一直计时，ti瞬间导通又关闭了]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690253.html]]></link>
 <author><![CDATA[曹石松]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 14 Aug 2015 00:11:43 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[T0没断开呀。要复位T0才行]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690243.html]]></link>
 <author><![CDATA[yexiong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 16:26:27 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[问题出在X2上，如果X2接通时间大于T0+T1即k60+K120=12秒则出现Y2不会OFF。
保证X2只接通一瞬间（一个脉冲）或使用T0的上升沿做Y2的启动信号。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690206.html]]></link>
 <author><![CDATA[雪花飘飘]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 13:47:11 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[晕死，你的程序本来就是让T1不断的重复定时的。定时到达，接通一个周期，复位，再开始定时。
一点也没有错。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690096.html]]></link>
 <author><![CDATA[lvpretend]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 04:14:01 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[同意7楼，或者将T0改成上升沿。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690042.html]]></link>
 <author><![CDATA[luohongliang]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 01:31:44 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[仿真？
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;那就不一定了。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690036.html]]></link>
 <author><![CDATA[zhtokokk]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 01:18:26 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[T0一直在工作 T0由X2引起，问题出在X2上，查一下X2是什么。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690029.html]]></link>
 <author><![CDATA[abcdef张勇]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 00:55:09 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[台達有時候是詭異了點...不過不是無解...試一下就能解決了 [s:28]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690025.html]]></link>
 <author><![CDATA[东华数字]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 00:50:00 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[当TI累计的12秒，瞬间断开Y2，Y2又瞬间断开TMR T1 K120,使TI常闭又复位，Y2又闭合，TMR T1 K120 动作重复。改进方法在最后这句Y2上并联T1常开自锁一下。最好采用SET 、RST写法，逻辑上比较清晰]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690023.html]]></link>
 <author><![CDATA[往事如风]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 00:25:04 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[T0 一直通了]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1690017.html]]></link>
 <author><![CDATA[yerong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 13 Aug 2015 00:10:16 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[把T0计时器线圈前加T1常闭触点 [s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1689967.html]]></link>
 <author><![CDATA[最远是多远]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 12 Aug 2015 13:52:56 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[加了以后两个定时器交叉计时，不断重复]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1689958.html]]></link>
 <author><![CDATA[行在中北]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 12 Aug 2015 13:18:22 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[改一下吧，在T0的前面加一个TI常闭。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1526622#1689957.html]]></link>
 <author><![CDATA[lqm003]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 12 Aug 2015 13:13:07 +0000]]></pubdate>
</item>
</channel></rss>