<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[蘑菇头急停按钮的接线]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222.html]]></link>
 <description><![CDATA[Latest 50 replies of 蘑菇头急停按钮的接线]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Fri, 15 May 2026 23:07:39 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[急停按钮正常情况下是1NO1NC配置。NC直接串在主控硬件回路里。NO给PLC一个 触发 信号。（注意是触发，并非常ON）
当拍下急停后，主回路断开，PLC获知NO点闭合做进一步处理。
紧急情况排除后，或者急停按钮意外失效后系统由于之前PLC进行了预处理。并不能接续运行。
此处引进复位按钮来复位PLC的处理。
按下启动按钮，接续 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1668625.html]]></link>
 <author><![CDATA[yfcc923]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 May 2015 01:13:14 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[按下急停断电，这符合正常人的思维方式，在程序和电路上要做相应的保护]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1668519.html]]></link>
 <author><![CDATA[yexiong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 May 2015 14:00:05 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[急停按钮是在紧急情况下切断控制电源而用，所以只有拍下才最快最符合人的本能，重新起动得按起动按钮，而且锁不住说明坏了就应该及时更换]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1668458.html]]></link>
 <author><![CDATA[wujianzzx]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 May 2015 11:59:08 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[1.根据安全习惯用接入常闭点是常用做法
2.无论是继电器回路还是PLC回路，编程和电路的绘制逻辑更加重要。应避免按下回路断开时时有些关键回路仍然有效。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1668356.html]]></link>
 <author><![CDATA[sunpeter]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 May 2015 05:41:58 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[既是叫急停，就是在紧急情况下以最快速度停止，就是要碰到它就停止了，接成弹起停止还怎么快得了，还不如用旋钮开关算了，而且你用接通作为停止的条件，万一那个触点失灵或是连接线断开了，都会停不下来，凡是作为保护的器件，正常情况下都应该是有信号通过的。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1668338.html]]></link>
 <author><![CDATA[百里长青]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 19 May 2015 04:01:08 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[接线还是按照约定俗成的比较好]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667903.html]]></link>
 <author><![CDATA[walkman]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 May 2015 01:27:09 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[同意7楼的说法。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667888.html]]></link>
 <author><![CDATA[gdj-gdj]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 May 2015 00:55:13 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[彈起的時候為常閉點]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667877.html]]></link>
 <author><![CDATA[东华数字]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 18 May 2015 00:41:21 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[pLC内部用常闭点，再用个区间复位指令]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667825.html]]></link>
 <author><![CDATA[520xht]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 17 May 2015 14:35:22 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[怎样接都可以 看设备的工艺]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667798.html]]></link>
 <author><![CDATA[xiaoyan88]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 17 May 2015 13:18:06 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[磨菇头急停按钮的接线是接常闭触点，在出现紧急情况时，按下就可以断开，在PLC为常开点，程序设计启动会自保，停止后不会自动启动。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667635.html]]></link>
 <author><![CDATA[liyanjunx]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 17 May 2015 00:59:57 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[习惯操作拍下去比较快且方便；急停输入按钮接常开点，PLC触点为常闭点；外接常闭点，PLC为常开点；程序设计启动会自保，停止后不会自动启动，只有重新启动。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667629.html]]></link>
 <author><![CDATA[fangzhihua]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 17 May 2015 00:17:13 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[你接常闭不就得了？既然是紧急停止急停，你说是用力拍下去快还是旋动再放手弹起才停的快？]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667578.html]]></link>
 <author><![CDATA[静芳]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 May 2015 13:52:10 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 蘑菇头急停按钮，弹起来是通的，拍下去是断开的。符合客观情况，紧急时，一掌拍下去就断开。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667543.html]]></link>
 <author><![CDATA[zhtokokk]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 May 2015 11:41:00 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我公司进口的美国设备，急停按钮的常闭和常开都在使用，包括安全门的安全开关，常闭和常开都接入PLC，就是防止一个触点出现故障，不起保护作用。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667388.html]]></link>
 <author><![CDATA[bg4igy]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 May 2015 03:15:39 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[蘑菇头的急停按钮设计的时候就是按下就急停的，想想紧急情况是直接按下去方便还是扭方便呢？对于失效安全，急停回路设计就应该是按下急停之后设备就停止了，急停松开机器要复位才能动作，这个不冲突的]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667364.html]]></link>
 <author><![CDATA[deeply]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 May 2015 02:26:54 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[按下急停，这样既符合人们的操作习惯，又符合人的本能。急停松开后，设备也是不能运行的。这也是要保证的。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667337.html]]></link>
 <author><![CDATA[sanlihu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 May 2015 00:57:21 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[急停按钮在继电接触器电路用常闭点的必须的，但在PLC使用常开触点对程序的编写更有利，在操作按下按钮急停符合正常的思维，操作也更快捷。在编程时用急停按钮的常开，在程序中使用急停的常闭触点也符合人的一般思维方式]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667308.html]]></link>
 <author><![CDATA[weisongyuan]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 May 2015 21:44:07 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[一般是按下急停，这样既符合人们的操作习惯，又符合人的本能，为了安全可以加安全继电器或安全PLC]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667294.html]]></link>
 <author><![CDATA[xiexonghui]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 May 2015 15:14:22 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[急停按钮必须是常闭点]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667290.html]]></link>
 <author><![CDATA[chenshiji618]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 May 2015 15:05:59 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[急停按下后设备就已经断电或复位了，再次接通也只是在初始状态，并不会继续动作，再次按下启动后才会继续动作，楼主要是不放心的话可以加个继电器自锁，我这边急停都是和主电源接触器自锁，按下急停后设备断电，按下启动后才会通电]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1485222#1667286.html]]></link>
 <author><![CDATA[892777011]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 May 2015 14:47:41 +0000]]></pubdate>
</item>
</channel></rss>