<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[步进电机驱动器和PLC怎么接线？]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280.html]]></link>
 <description><![CDATA[Latest 50 replies of 步进电机驱动器和PLC怎么接线？]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Sat, 16 May 2026 21:15:36 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[恩，谢谢各位不涩吝惜的指导，小弟一定会加倍努力学习的。THANKS AGAGIN!!]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1596390.html]]></link>
 <author><![CDATA[quzhihua]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 22 Aug 2014 04:51:34 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[CPU 222 CN DC/DC/DC是输入输出都是DC24V，CPU 222 CN AC/DC/DC是输入是AC120/240V输出是DC24V。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1595659.html]]></link>
 <author><![CDATA[hexdho]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 20 Aug 2014 01:50:50 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[劝楼主还是先把基本的电路学会，在来学步进伺服。PLC型号选错，基础的电路不会接，程序还怎么编。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594809.html]]></link>
 <author><![CDATA[isnow2005]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 15:01:36 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[s:21]&nbsp;&nbsp;[s:21]&nbsp;&nbsp;[s:21]&nbsp;&nbsp;[s:21]&nbsp;&nbsp;[s:21]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594698.html]]></link>
 <author><![CDATA[sz518104]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 02:42:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[这个貌似步进驱动器的说明书都会有详细的接线图的，参考着接就好了，共阳极PUL+DIR+，一起接高电位，共阴极PUL-,DIR-接低电位，限流电阻阻值说明书里会给出的，PLC应该用晶体管输出的]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594696.html]]></link>
 <author><![CDATA[mythic]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 02:28:30 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[从上图中可以看出，输出电压是根据1M（2M）和1L+（2L+）所连接的电源决定的。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594695.html]]></link>
 <author><![CDATA[wwcwwc]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 02:27:40 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[给一张图你看看，应该可以明白了 [attachment=124757]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594693.html]]></link>
 <author><![CDATA[wwcwwc]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 02:25:33 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[附议6楼，具体点就是你Q输出公共端接的是什么信号，那么Q就输出什么信号，比如你公共端接的是24V-,那么Q0 ,Q1就输出24V-低电平信号，你的步进电机驱动器PUL-接Q0.0输出脉冲，DIR-就可接Q0.1脉冲方向控制；PUL+&nbsp;&nbsp;DIR+可以用共阳极接法，接DC5V+电源，如果你用的是DC24V开关电源，记得串2K的电阻限流]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594679.html]]></link>
 <author><![CDATA[gc007008]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 01:53:16 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[s:28] 回楼上的，Q输出只是一个开关点而已，公共端接多少就是输出多少，跟其他无关]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594667.html]]></link>
 <author><![CDATA[hot_cha]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sat, 16 Aug 2014 00:55:14 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[4楼的你好，
我给西门子的客服打了电话了，Q0.0和Q0.1的输出电压是和电源一致的。220v的电源，则输出点Q的电压都是220v的，如果电源24DC，则输出点Q的电压都是24v的，好像是个新来的客服给我解释的，感觉她也不是很自信氏的，我的PLC要不要选个晶闸管输出的？]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594544.html]]></link>
 <author><![CDATA[quzhihua]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 Aug 2014 08:27:12 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[PLC是AC220供电电源的，Q0.0和Q0.1输出的电压是DV24V.PUL+接脉冲输出口Q0.0,PUL- 接DV0V. DIR+接脉冲输出口Q0.1,DIR- 接DV0V. 若步进电机PUL+是5V的话串一个2K电阻.]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594453.html]]></link>
 <author><![CDATA[hexdho]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 15 Aug 2014 02:47:06 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[1楼的大哥，
PUL+和DIR+连在一起，PUL-&nbsp;&nbsp;接脉冲输出口Q0.0，DIR-接控制方向输出口Q0.1，是这样的吗？
还有一点，如果我的PLC是AC220供电电源的，那么Q0.0和Q0.1输出的电压是多少呀？这种情况该怎么连接呀？
小弟很菜的 [s:28]]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594282.html]]></link>
 <author><![CDATA[quzhihua]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 14 Aug 2014 09:49:17 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[应该可以买个集电极转差分的东东]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594273.html]]></link>
 <author><![CDATA[xijiangli789]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 14 Aug 2014 09:30:41 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[问题回复]]></title>
 <description><![CDATA[不是这样的，PUL+&nbsp;&nbsp;\PUL- 是一组作为速度信号，DIR+\DIR-是一组作为方向信号。2个输出口就可以了。
连接时，将各个正都连接在一起，负连接到各自的输出端子上。如果是24V电压需要用限流电阻，如果是5V电源直接连接。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1463280#1594271.html]]></link>
 <author><![CDATA[wwcwwc]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 14 Aug 2014 09:05:57 +0000]]></pubdate>
</item>
</channel></rss>