<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[伺服马达回原点精度？]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384.html]]></link>
 <description><![CDATA[Latest 50 replies of 伺服马达回原点精度？]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Sun, 03 May 2026 22:50:52 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[我一般有用机械开关，精度在2个μ以内。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1507233.html]]></link>
 <author><![CDATA[hafatahaha]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 08 Nov 2013 08:34:33 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[Z相比较精确些&nbsp;&nbsp;如果对位置要求比较精确&nbsp;&nbsp;你可以使用绝对值控制模式 这样就减少了回零造成的误差]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1507200.html]]></link>
 <author><![CDATA[流洒]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 08 Nov 2013 07:48:54 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用伺服原点信号，即z信号，另外不要用传感器（光电，接近开关），用机械开关比较稳定，如行程开关&nbsp;&nbsp; 我们就是这么做的]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1502446.html]]></link>
 <author><![CDATA[elec_xu]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 28 Oct 2013 11:16:50 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[回原点速度是关键 还有是直接让驱动器回效果肯定好]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1501787.html]]></link>
 <author><![CDATA[yerong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Sun, 27 Oct 2013 01:41:35 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[感应器不太重要,用Z相比较准啊!]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1499725.html]]></link>
 <author><![CDATA[wangming]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Tue, 22 Oct 2013 06:20:54 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[光纤有延时输出功能的，要注意了，选用什么零点开关主要是看工作环境，像机床可能用不来光电开关]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1495139.html]]></link>
 <author><![CDATA[langman]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 10 Oct 2013 09:13:31 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[为什么你不用伺服的Z相来做原点]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1494893.html]]></link>
 <author><![CDATA[yamqq]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 09 Oct 2013 15:03:04 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[SEW 回原点精度100%，我用过]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1494693.html]]></link>
 <author><![CDATA[yiyang1]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 09 Oct 2013 06:48:04 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[没朋友帮忙解答下吗？]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-1439384#1494691.html]]></link>
 <author><![CDATA[gaokunjian]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Wed, 09 Oct 2013 06:30:36 +0000]]></pubdate>
</item>
</channel></rss>