<?xml version="1.0" encoding="gbk"?>
<rss version="2.0">
<channel>
 <title><![CDATA[问题 要求两轴转动时，转速比严格不变，如 ..]]></title>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404.html]]></link>
 <description><![CDATA[Latest 50 replies of 问题 要求两轴转动时，转速比严格不变，如 ..]]></description>
 <copyright><![CDATA[Copyright(C) 工控人家园]]></copyright>
 <generator><![CDATA[www.ymmfa.com]]></generator>
 <lastBuildDate><![CDATA[Mon, 11 May 2026 18:39:04 +0000]]></lastBuildDate>
  <image>
 <url><![CDATA[images/rss.gif]]></url>
 <title><![CDATA[工控人家园]]></title>
 <link><![CDATA[http://www.ymmfa.com]]></link>
 <description><![CDATA[工控人家园]]></description>
  </image>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[两个电机的功率是多大？？是什么负载？？如果确实是要求精度很高的话就用两伺服带两个电机，把其中一个设为基准，用位置模式控制，作为基准一方的控制器输出一组脉冲信号作为另一个电机控制器的脉冲输入信号，它们的速比就在参数里用齿轮比实现，这样只要你改变基准电机的速度，在几MS里另一个电机就会跟上基准电机的速度 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#210212.html]]></link>
 <author><![CDATA[dv0429]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 21 Apr 2008 15:28:24 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[你可以用一个变频器带两台电机，只要变频器大于电机1.5倍及可啊，电机总功率1.5啊]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#210150.html]]></link>
 <author><![CDATA[a888888]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 21 Apr 2008 13:40:46 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[[quote]引用第6楼pzzy于2008-04-21 10:20发表的&nbsp; :
说清楚一下这个项目：首先，机械齿轮一定不行的，因为两个转动轴离的很远。
&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 转速上，大概每秒5,6就可以了。这个不做具体要求
&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &n ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#209830.html]]></link>
 <author><![CDATA[cvlsam]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 21 Apr 2008 04:16:14 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[可以考虑3楼最后的一个方案]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#209824.html]]></link>
 <author><![CDATA[adidas]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 21 Apr 2008 03:49:25 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[说清楚一下这个项目：首先，机械齿轮一定不行的，因为两个转动轴离的很远。
&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 转速上，大概每秒5,6就可以了。这个不做具体要求
&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 关键是同步性，因为后面要接，允许的误差越小 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#209772.html]]></link>
 <author><![CDATA[pzzy]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Mon, 21 Apr 2008 02:20:19 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用机械的方法来解决这个问题最简单，一个电机带两个轴，通过机械结构将两轴连接，速比稳定。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#208125.html]]></link>
 <author><![CDATA[shenwq]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 18 Apr 2008 07:51:02 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[楼主：你得把问题说清楚。

转速要求严格保持一致？在电气控制中，转速保持同步，只是一个检测---控制---再检测--再控制的循环过程，你最好说清楚：两台电机最大允许的不同步范围是多少？工艺上出现不同步后在多长时间内必须恢复同步。
按楼主所说转速并不快，其实机械设备转速绝大多数都不能和电气装置的监测控制速度相比 ..]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#208116.html]]></link>
 <author><![CDATA[zxdha]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 18 Apr 2008 07:43:48 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用齿轮 或齿形带， 好处：简单 坏处：变速比麻烦

用脉冲控制电机转动 好处：变速比简单 坏处：复杂，成本高

用编码器检测作同步控制 好处：变速比简单 坏处：复杂，成本较高

用两个变频器，转速用同一个模拟量控制 好处：变速比简单 坏处：可能不是非常严格。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#207836.html]]></link>
 <author><![CDATA[yerong]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Fri, 18 Apr 2008 00:39:35 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[一楼高招。哈哈哈哈哈]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#207810.html]]></link>
 <author><![CDATA[雪花飘飘]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 17 Apr 2008 18:08:55 +0000]]></pubdate>
</item>
<item>
 <title><![CDATA[]]></title>
 <description><![CDATA[用一台电机，带两个轴。]]></description>
 <link><![CDATA[http://www.ymmfa.com/read-gktid-12404#207557.html]]></link>
 <author><![CDATA[sjm213]]></author>
 <category><![CDATA[综合讨论]]></category>
 <pubdate><![CDATA[Thu, 17 Apr 2008 09:33:15 +0000]]></pubdate>
</item>
</channel></rss>